Steam Shower Enclosures Uk
Steam Shower Construction
So you have now purchased your new steam shower cabin direct from the store and would like to test it out! The following guide is written to explain the key steps that will be involved during the course of a steam shower fitting and point out some common easy-to-avoid installation problems.
1. Check your Product
It is important you check that your product happens to be shipped without damage or visual defect before you start any installation. You are advised to make these inspections prior to making a reservation for a plumber or installation engineer. Any damages should be noted using the driver upon delivery and detailed to The supplier inside of 48 hours of delivery.
For even more on steam shower installations click right here
2. Choosing a Certified Installer
Water is an effective conductor of electricity therefore the installation of electrical wiring in a bathroom is generally a hazardous job. We strongly advise that every electrical work is carried out by a qualified professional. It is advisable to select a plumber who also offers a part P certification. This will certainly signify that the plumber is qualified to carry out the electrical work required during the steam shower installation.
3. Preparatory Work
Just before purchasing you ought to have confirmed the cabin measurements and know where within the bathroom you will be positioning the steam shower. The steam shower installation will need both a hot and cold water supply together with an electrical feed.
Water Supply: The manufacturer's steam shower installation booklet will provide measurements to where the hot and cold feeds should be piped. The water supply pressure level ought to be 2bar shower system dependant, which equals to a combined flow rate of 12-16 litres per minute across both supplies. The source water supply really should be balanced across the hot and cold supply, that can be achieved making use of a pressure equalising valve (PEV) or pressure reducing valve if required. The steam shower will arrive with hot and cold braided hoses upon the rear for the unit allowing the unit to be connected and pushed straight into position. The water supply pipes ought to be recessed and not protrude more than ½ inch out from the wall. Ball lever valves are generally installed to permit quick shut-from the water.
Electrical Supply: The 3.0KW steam generators require a 13Amp dedicated power supply to the steam shower. Typically, that should be wired back to the consumer box and can be located on a different breaker switch. Please make sure that either the RCD on the steam showers power cable or an RCD inside the consumer box is utilised. The rated functioning voltage of the majority of the steam showers is 220V at 50Hz, by using the controlling circuit operating at DC 12V.
Drainage: The manufacturer's installation booklet can give dimensions for setting the shower's drainage point. For the most part, the shower comes with a flexible waste hose that'll be connected to your drainage point. You should check out the clearance under the shower tray.
Telephone point: when the steam shower you will be installing will come with a phone input then you have the option to run a telephone access point into the rear from the unit.
At this time you should carry out preparatory decoration as necessary. This may involve plastering, painting or tiling. CAUTION: Never knock nails or drill holes into walls with no knowledge of what is hidden behind them!
4. Tray
Place the shower tray in its finalized standing location. Adapt the screw legs which happen to be positioned under the bottom for the tray up until the point when the tray is level. This should be checked by making use of a spirit level. When the tray is level tighten up the securing nuts to secure the height of each leg.
5. Top
Relocate the tray out of the wall around 40-60cm to allow access to all sides belonging to the cabin during the course of the installation. Your order of panel placement should stick to the specified shower installation instructions. Each panel should align by using the pre-drilled holes into the tray and adjoining panels. Place sealant between each adjoining panel and also in between each panel and also the tray. Work with the bolts supplied to securely attach each panel together. When all acrylic and glass panels appear to have been secured the very best piece can be placed onto the side panels. Use the bolts/screws provided to securely secure the top piece to the side panels.
You can discover various wonderful instances of steam shower units units right here
6. Mirror, Accessories
Mirror: You certainly will need two people to install the mirror. The first person will keep the mirror into position inside the shower as the second can fasten the bolt fixings behind the shower. Once fixed it is important to administer a bead of sealant around the mirror and all over the fixing holes. This is really important to prevent water and steam coming into connection with the mirror's foil backing. If not sealed properly then as time passes the mirror may begin to discolour.
Handles: Simply attach the handles with each other on either side of the glass doors.
Accessories: for the most part, the shower should come with one or two shower hoses. Connect one end of this hose into the connector upon the back panel therefore the other end into the handheld shower and foot massage unit, if relevant. Please be sure that the hoses are connected the correct way around. Failure to do so may result in water leaking out between the hose and also the connector thread. When the steam shower accepts CD/MP3 input then chances are you can connect the audio cable into the control box at this time and run it returning to your music player.
Seals: slip the shower seals/fins onto the fixed glass panels adjacent to the door and on the door glass itself. Adjust the doorway as necessary to reduce any gaps where steam will break free.
Even more steam showers can be enjoyed at this website
7. Connect Adjoining Pipes
The overhead fan, lights and speaker systems will all be operated through the main control box. Each wire should be labelled and have matching connectors that come direct from the control box. These 12V DC wires ought to now be plugged together. The shower will have water pipes that run towards the overhead shower and body jets out from the 3-way thermostatic valve. These really should be plugged straight into the corresponding connectors and tightened up using the metallic pipe clips and a Phillips screwdriver.
8. Connect Water, Electrics
Please double check that the water supplies are well balanced as well as a sufficient pressure. If necessary and depending on your water system you may be able to connect a water pump to boost the supply pressure. At this time you must connect the hot and cold water supplies using the 15mm braided hoses supplied. The braided hoses use a standard 22mm connector.
Connect the RCD that comes connected to the power cable to a wall or an accessible access point. Alternatively, use a dedicated RCD back during the consumer box. A dedicated 16Amp supply is required via an isolated fused spur connected directly returning to the customer box. Alternativley, the steam shower are often powered via an IP56 rated wall socket.
It is necessary that the earth wire is connected to an earthing part of the bathroom or even the metal framing from the shower. The installer will have the ability to advise about correct earthing of all of the steam shower.
Finally, connect the flexible water hose into your bathroom waste point and seal as necessary.
Heres an additional whirlpool steam shower online store you may appreciate
9. Sealant
Typically, you will want to now place a bead of white or clear sealant between the adjoining side panels. Sealant must also be placed between the side panels and also the tray to get rid of any water running along any seams and over the side of the shower tray.
Once sealant has been applied and allowed to dry, the steam shower ought to be tested for water tightness. Make use of the handheld shower to spray water against the water jets, all acrylic/glass panel fixing holes and along the join of all of the adjoining panels. Typically, it is really not necessary to seal the top piece but that is left to the discretion of this installer. Check around the rear and sides from the steam shower to see whether any water has escaped and reseal where necessary. Also, the installer should check that all pipes are fully spanner tightened and not dripping any water.
Once the unit has been fully checked for water leaks and all electrical features such as lights, radio and steam tested then gently push the unit back into position.